Solids control mud cleaner in U.S. for oil and gas drilling

GN Solids America, it is the branch company of GN Solids Control Company Limited. It is located in Houston Texas. With its own office building and warehouse.

GN Solids Control and GN Solids America took part in 2015 OTC oil show with great success. The head company GN Solids Control takes its latest design drilling waste management equipment (high speed decanter centrifuge, vertical cuttings dryer) for the show. And GN Solids America show the mud cleaner separator machine for the OTC oil show. Mud cleaner is a 3-in-1 machine, with the function of desander, desilter, and a under flow shale shaker.

GN solids control mud cleaner for oil and gas drilling showing on OTC
1) Mud cleaner model: GNZJ594E-2S12N
It is the combination of under flow shale shaker GNZS594E, a 2-cone desander, and 12-cone desilter.
2) Capacity of the mud cleaner: 240m3/h (max.)
The capacity of mud cleaner depends on the desander cone and desilter cone capacity. The smaller one is the treating capacity of the whole treating capacity.
Desander cone and desilter cone is on D100 separation machine. There will be some amount of useful mud discharged together with dirty mud. So the function of underflow shale shaker is to further treat and recovery mud and dry the solids discharge.
Some jobsite may use desander or desilter with not under flow shale shaker to save cost. But the performance is surely not as good as the combined one.
3) Feeding pipe size of the mud cleaner is 6’’ and the output size if 8’’. GNSB8*6 centrifugal pump is mostly used to feeding for the desander and desilter.
4) Shaker screen of the GNZJ594E-2S12N mud cleaner: the under flow shale shaker is a 4-panel shaker with long shaker deck. It can make the solids more dryer. The shaker screen is pretention type, and mounted with wedge for fast screen changing.
5) GN patent design for Synchronous adjusting of the deck angle. When the operator adjust shaker angle at any side, both sides will be up or down with exactly the same angle. It saves time of jobsite people and easy for operation.  

Chemical enhance dewatering unit with centrifuge

Drilling waste decanter centrifuge can be used together with Chemical enhance dewatering unit. We call it dewatering unit. The total system is normally put in a 20ft container or a 40ft container, per customers’ request.

Chemical enhance dewatering unit, frankly speaking, it is a mixing system for chemicals. Chemical can be mixing and storage in the system per the set conditions. And then the qualified chemicals can be transferred to decanter centrifuge feeding pipe and mixed with mud before center into centrifuge for treatment.

Some customer is wondering: the decanter centrifuge is used to separate the fine solids from drilling mud, why chemical enhance dewatering unit is need together? And in which condition, the chemical enhance dewatering unit is needed?
The reason is that, decanter centrifuge is a kind of physical separation. It applies high G force and the differential speed to separate fine solids above 2 ~ 5 microns from drilling mud. For the even more fine solids smaller than 2 ~ 5 microns, decanter centrifuge is not worktable. They will be left in the fluids after separation. If customer want to separate this part of the ultra fine solids and get more pure water, chemical treatment is requested.    
The function of the chemical enhance is to make the fine solids in a bigger size, in this case, decanter centrifuge can treat it.

Then customer have another question, how they get the chemicals? How should they know which kind of chemicals should be add? How much should be add? How long time should be wait? How long time for mixing with drilling mud? If they buy centrifuge dewatering unit from GN Solids Control, can GN company offer chemicals to them? …
Answers as below: The centrifuge manufacturer or dewatering unit manufacturer, they normally only make the machine, they do not supplier chemicals. There are chemical company for all the jobs. What you should do then is to find a reliable chemical supplier, send them samples of your materials, and tell them result you want to get, the chemical engineer will test and offer you the suitable chemicals and instruct you how to use it.

Middle speed centrifuge for mud recovery system or barite recovery

GNLW452 is an economic standard decanter centrifuge. It is specially designed and made by China top solids control manufacturer – GN Solids Control Company. It is a basic centrifuge model for middle speed. It is widely used for barite recovery. Another popular function is to reduce the weight of high gravity mud, like used in HDD mud system to reduce the weight of the mud.

Parameters of GNLW452 middle speed decanter centrifuge for mud recovery system or barite recovery.

Dimension: The centrifuge is with 450 mm (18 in) bowl diameter and 1105 mm (43 in) in length. So some customer called it big bowl centrifuge.
Speed and G force: The max. bowl speed is 1800 rpm and the typical speed is also 1800 rpm. G force under 1800rpm is 815. Differential speed is 32rpm @ 1800rpm. In some cased, drilling site may need a lower speed, in the condition that, the mud weight is big, or want a bigger capacity, GN Solids Control can offer another set of pulley and belt to get a lower fixed speed, like 1200 rpm. In this case, customers only need to change the pulley and belt to lower down the speed.
Separation point: 5~7 microns. It means, it can remove solids bigger than 5 ~ 7 microns. Bigger than this point, the solids will remain in the mud. For HDD mud recovery system, this separation point is good. And when GNLW452 is used for barite recovery or used to reduce the weight of the mud, it is mainly used for pre-separation. There normally will be another set of high speed centrifuge for fine solids separation.
Recommended feeding pump for GNLW452 centrifuge is 11kw (15hp) screw pump. GN Solids Control recommended German brand NETZSCH pump feeding for the centrifuge.

Advantages of GNLW452 middle speed decanter centrifuge for mud recovery system or barite recovery
1) Single motor design for more compact design
2) Screw protection is interchangeable ceramic tile for longer lifetime and easy maintenance.
3) Screw flow distribution port and bowl solids discharge port protected by tungsten carbide alloy.
4) Easily adjustable liquid discharge weir height for flexible application.

Centrifugal pump with control panel for drilling rig

Centrifugal pump can also be called sand pump. It is widely used for oil and gas drilling rig mud system. It can be used as mixing pump, desander desilter feeding pump, centrifuge feeding pump, trip pump, charging pump etc…

There are different functions of centrifugal pump in oil and gas drilling rig mud system

1) Centrifugal feeding pump
Centrifugal pump can be used as feeding pump for desander, desilter and decanter centrifuge. It is normally mounted on the slope tank or skid of the mud tank.

2) Mixing pump
Centrifugal pump can be used together with mixing hopper as the mud mixing system. There are 2 type of mixing mud system with centrifugal pump.
One kind of design is both the centrifugal pump and mixing hopper with ventury are mounted on a separate skid, they are connected through pipes and values. And then connected to mud tank.
Another kind of design is more compact. It is built-in design onto the system. The centrifugal pump is mounted on the same tank skid, while the mixing hopper can be mounted on the tank top or on the tank skid.

3) Trip tank pump
Trip tank (5~10 cbm) is normally equipped for oil and gas drilling rig mud system. It is before shale shaker tank. And a small motor size centrifugal pump is requested for the trip tank.

4) Degasser pump
For European made vacuum degasser, it is not self suction type. A separate degasser pump is requested to generate vacuum for the degasser.
Unlike European brand vacuum degasser, GN Solids Control made degasser is self suction type. It does not need degasser pump. It can save the power of the total mud system.

Customer can also use centrifugal pump with other functions. GN Solids Control makes centrifugal pump from 15hp to 100hp, with size vary from 4×3 to 8×6 to suits for different applications.

GN Solids Control is certified for manufacturing of explosion proof control panel. Both the centrifugal pump and control panel can be mounted on the same skid for easy movement. If you need other customization, you can contact GN group for help.

New Driling Waste Management System Shown in Sichuan, China

image

Right now, a national Oil Show is beingheld in Sichuan Province, China. Many companies, both from domestic China andabroad, are attending the Oil Show. For this Oil Show, GN Solids Control showed
the newly designed drilling waste management system GNDC-40B.

Sichuan Province is located in south east
of China, in which there are several drilling rig suppliers and oil field
service companies. Some international oil companies also have branch or jobsite
there. Just last year, this same system which GN are showing for the oil show
was chosen by a jobsite of SHELL, in Sichuan Province.

This system is combined by following
equipments:

1.      
GNLW363 Decanter Centrifuge.
this centrifuge is a 14 inch bowl decanter centrifuge.
for the same model, GN has developed to the 3rd generation, with
lots of improvements. Each year, GN sells 150 sets of centrifuges, 70% of which
are this model. This centrifuge could provide various applications for oil and
gas drilling projects, like solids control decanter centrifuge, waste
management decanter centrifuge and dewatering centrifuge. For the same model,
GN has fixed speed one and vfd control panel one for option, for fixed speed
one, GN could provide 3 optional belt and pulley for the end user to use it in
different conditions, and for VFD controlled one, more optional speed could be
reached by means of the 3 VFD controlled models for main motor, back motor and
feeding pump.

2.      
Vertical cuttings dryers, this
is the former step separation equipment for decanter centrifuge. Since GN
designed the first vertical cuttings dryer in China, GNCD series vertical cuttings dryer has
been to the 3rd generation. This newly improved model GNCD930C is
proved to suit for not only OBM and SBM as traditional vertical cuttings
dryers, but also suitable for WBM. For the Vertical Cuttings dryer, GN also
have fixed speeded and VFD controlled available.

If you miss the Sichuan Oil Show but still
like to see GN products, you could arrange your schedule to Beijing Oil Show,
the biggest Oil Show CIPPE. In CIPPE, GN will have a larger booth and show
more equipments and systems.

GN Booth number : E1-E360.

Time: March 26th – 28th.

.

Related Arciels: